 |
|
| |
Integrated Motor+Driver+Encoder/ SilverPak 23DE |
 |
 Operates from +12 to 48 VDC with certain currents*
Selectable phase currents from 0.3 to 3.0 Amps Peak with certain voltages*
Step resolutions from half step to 256x microstepping
Four selectable damping modes
Smooth motion
Three optically isolated control inputs and one optically isolated control output
Hold current reduction capability with adjustble current and timeout setting
Pole Damping Technology ™
On Board Encoder
* Please refer to Electrical Specs section for further details
 |
 |
|
 |
|
|
|
|
|
 |
Encoder features:
• Max 1,250 cycles per revolution (CPR)
• Max 5,000 pulses per revolution (PPR) (quadrature)
• 2 channel quadrature TTL squarewave outputs
• Optional index (3rd channel)
• Position correction capabilities
Pole Damping Technology ™
Pole Damping Technology™ (PDT) enhances step motor performance by dampening each full step in order to create a more accurate and smooth motion profile. Microstepping the step motor will optimize Pole Damping™ Technology. PDT outputs the correct amount of run and hold currents to the motor. Thus, it will overcome the step motor’s natural tendency to want to forcefully pull towards the full step ON position.
For more information, click here
|
|
|
|
 |
- OPERATES FROM +12 to 48 VDC with certain currents *
- SELECTABLE PHASE CURRENTS FROM 0.3 TO 3.0 Amps Peak with certain voltages *
- ISOLATED INPUTS:Step, Direction, and disable
- STEP FREQUENCY (MAX): 2.5 MHz
- STEPS PER REVOLUTION (1.8° MOTOR): 400, 800, 1600, 3200, 6400, 12800, 25600, 51200
- MICROSTEP RESOLUTIONS (1.8° MOTOR): 2X, 4X, 8X, 16X, 32X, 64X, 128X, 256X
* The SilverPak 23D can handle a 24VDC and 3 Amp system OR a 48VDC and 2 Amp system. |
|
|
|
|
 |
Motor Front Shaft Extension Length
Standard length is 0.81”.
Motor Shaft Diameter
Standard shaft diameter is 0.25”.
|
Overall Body Length
Motor body length is available in various lengths (Dimension A):
DE-5718X-XX :3.17 " MAX
DE-5718M-XX:3.61 " MAX
DE-5718L-XX:4.54 " MAX |
 |
|
|
|
 |
 |
| A female DB-9 connector cable receives power and provides the control connections for the Silverpak 23D unit. Active signals are optically isolated. An open collector drive is required to provide pulses for Step, levels for Direction, and Disable/Enable. |
 |
| Pin |
Function |
Description |
1 & 6 |
PWR +ve |
Motor Supply Voltage. +15 to 48 VDC |
2 & 7 |
PWR –ve |
The ground or return of the power supply connects here |
3 |
+5VDC Out |
Used to Power the logic functions |
4 |
Step |
Connects to the open collector drive. |
5 |
Disable |
This input is used to enable/disable the output of thedriver |
8 |
Opto Supply |
+5 VDC input used to supply power to the isolated logic inputs. A resistor must be used if the supply isgreater than 5 VDC |
9 |
Direction |
This input is used to change the rotation direction ofthe motor |
|
|
|
|
|
 |
| Lin Engineering can design and manufactures stepper motors specific to your environmental, mechanical, and dimensional requirements for step motors. click on image to view our options |
|
|
 |
|
Lin Engineering step motors are available with either 2-coil Bipolar, or 4-coil Unipolar windings. Bipolar motors have 4 leads, while unipolar motors have 6 leads. Additionally, some stepper motors are designed with 8 leads, so they may be connected in a variety of ways.
Click here to view our connection instruction
|
|
 |
Address: 1990 Russell Avenue , Santa Clara, CA 95054
Tel: (408) 919-0200 Fax: (408) 919-0201
Email: sales@linengineering.com, techsupport@linengineering.com
To find your local sales office, click here
|
|
|
 |
 Silverpak 23DE Manual
3D MODEL IN .stp and .ipt format 
 3D-Model DE-5718X
3D-Model DE-5718M
3D-Model DE-5718L
|
|
 |
| |
|
|
|
